Serving the Huntsville area  ·  (256) 858-7133  ·  Open Mon-Sun 7am-7pm
📞 (256) 858-7133 Free Quote

Metal Roofing in Gurley, AL (35748) · Local Professionals

Huntsville Metal Roofing · Fast response in Gurley and the Huntsville area · Free estimate 24h

✅ Licensed Contractor 🛡️ Licensed & Insured 💸 Free Quote 24h 🕐 Mon-Sun 7am-7pm
+306Verified Reviews
10Years in Business
4.9 ★Google Rating
24/7Available
✅ No hidden fees💳 Cards accepted🛡️ Licensed & Insured

Gurley is a small town where the lots are wide, the driveways are long, and a lot of the roofs are on barns, shops, and farmhouses that have seen a few decades of Alabama weather. If you live off Highway 72 or down a gravel road near the Paint Rock River, you know that metal roofing just makes sense here.

Homeowners in Gurley (35748) call Huntsville Metal Roofing because we understand the difference between a quick patch on a shed and a full standing seam install on a house. We are based in Huntsville, just a short drive up the road, and we bring the same crew and the same standards to every job, whether it is a cabin near the Madison County Nature Trail or a commercial building on County Line Road.

Metal Roofing in Gurley (35748)

Gurley is rural, and that changes the work. Properties here often sit on an acre or more, with a mix of pasture, gravel drives, and mature hardwoods. That means we deal with tight turns for equipment, long runs of fence to protect, and roofs that are sometimes a quarter mile from the nearest power drop. The ground is red clay and limestone, so drainage matters. We make sure gutters and downspouts are sized right and that water is pushed away from the foundation, not just off the roof. Farm buildings and shops often have corrugated or ribbed panels that have been screwed down for years. We know how to replace fasteners, re-seat washers, and stop leaks without tearing off a perfectly good panel.

Our team has worked on everything from old farmhouses with steep gables to newer brick homes with complex hips. We have installed standing seam on homes near the Gurley Community Center and repaired R-panel on barns out toward Maysville. If you are not sure what you have, we will tell you straight.

Our services in Gurley

How a Job Works in Gurley

Step 1: You call (256) 858-7133 or request a free estimate online. We schedule a time to walk the property with you, take measurements, and look at the roof, flashing, and drainage. We will tell you what needs repair now and what can wait. No pressure, no sales pitch.

Step 2: Once you approve the scope and price, we pull the permit if one is required by the local building department and schedule the work. In Gurley, that often means coordinating with a homeowner who has a long driveway or a gate code. We handle the logistics, protect your landscaping, and keep the job site tidy. If your property is in a historic district or has an HOA, we will help you understand what panel profiles and colors are allowed before we order materials.

Step 3: When the work is done, we walk the roof with you, show you the finished product, and make sure you are satisfied. We clean up every nail, scrap, and wrapper. We leave your property the way we found it, only with a better roof.

Pricing in Gurley depends on the size and pitch of your roof, the condition of the decking, and how accessible the property is. For a typical ranch home, metal roof installation starts at $8 per square foot, and standing seam starts at $10 per square foot. If you are replacing an existing shingle roof, replacement starts at $9 per square foot, and a retrofit over shingles starts at $7 per square foot. Repairs start at $450, and screw replacement or re-fastening starts at $750. For barns and shops, corrugated and ribbed panel roofing starts at $5.50 per square foot. We always provide a free estimate so you know the real number before we start. Call (256) 858-7133 to schedule yours.

My barn off County Line Road has corrugated panels that are pulling loose at the screws. Can you fix that without replacing the whole roof?
Yes. That is one of the most common jobs we do in Gurley. We replace the failed screws with new fasteners and washers, re-seat any panels that have backed out, and check the purlins for rot or damage. If the panels are still solid, a screw replacement and re-fastening job starting at $750 can add years to the roof. We will inspect the whole roof and tell you if a full replacement makes more sense.
A storm just blew through and lifted some panels on my roof near the Gurley Community Center. How fast can you get out?
We offer free storm and wind damage inspections and prioritize emergency calls. Call (256) 858-7133 and we will schedule the soonest available visit, usually within a day or two depending on the volume of storm calls. We can tarp or secure the roof temporarily if needed and provide a written estimate for the repair.
What does a metal roof cost for a typical three-bedroom house in Gurley?
For a standard ranch or two-story home, most installations fall between $8 and $12 per square foot depending on the material and complexity. That means a 2,000 square foot roof could range from around $16,000 to $24,000 for installation. Repairs are much less, starting at $450. The exact price depends on roof pitch, number of penetrations, and whether we are going over existing shingles or doing a full tear-off.
Do I need a permit for a metal roof in Gurley?
Roofing permits are commonly required for a full replacement or re-roof in Madison County, and the rules can vary. We always check with the local building department before starting work and pull the permit if needed. We will handle that part of the process for you so you do not have to worry about it.
My neighbor's tree branches hang over my property line and drop limbs on my roof. What can I do?
That is a common situation in Gurley with all the mature oaks and hickories. Legally, you can trim branches that overhang your property line, but it is best to talk with your neighbor first. If a limb falls and damages your roof, your insurance may cover the repair, and we can provide a detailed inspection report and photos to support your claim. We do not get involved in neighbor disputes, but we can document the damage clearly.
Are you insured for work on my property in Gurley?
Yes, we are fully insured with general liability and workers' compensation coverage. That protects you and your property if anything goes wrong.
What should I do to maintain my metal roof in Gurley between storms?
Check the fasteners and washers once a year, especially after a windy spring. Look for any panels that have lifted or seams that have separated. Keep gutters clear of pine needles and leaves, and trim back tree limbs that rub the roof. If you see rust spots on a corrugated roof, a metal roof coating starting at $2.50 per square foot can extend its life. We offer free inspections if you want a professional opinion.
Why choose us?

Trusted professionals in Huntsville

🏅

Licensed contractors

Continuous training, professional equipment, meticulous and code-compliant work

🛡️

Licensed & Insured

Full coverage on all our job sites, no exceptions

⚡

Available Mon-Sun 7am-7pm

Emergencies, weekends, holidays: available when you need us

💰

100% Free Quote

Response within 24h, no commitment, by phone or form

Our services

Our Metal Roofing Services in Huntsville

All your work handled by qualified professionals in Huntsville

Metal Roof Installation

Complete metal roof systems engineered for your local climate and built to outlast three shingle roofs.

Included in your service

  • Deck inspection and repair before any panel goes on
  • High-temp synthetic underlayment and correct ridge and soffit ventilation
  • Manufacturer-certified panel, trim, and flashing details for the full warranty
  • Free on-site assessment and written estimate within 24h
Learn more→

Standing Seam Metal Roofing

Concealed-fastener standing seam: no exposed screws to loosen, leak, or need re-torquing.

Included in your service

  • Panels roll-formed to the exact length of your roof, no end laps
  • Mechanically seamed or snap-lock profiles with concealed clips
  • Floating clip system that lets panels expand and contract freely
  • Kynar 500 / PVDF finish in the full architectural color range
Learn more→

Metal Roof Replacement

Full tear-off of an end-of-life shingle, cedar, or metal roof, replaced with a complete new system.

Included in your service

  • Tear-off and haul-away of the old roofing, dumpster included
  • Decking inspected board by board, rot and soft spots replaced
  • New underlayment, drip edge, valleys, and penetration flashing throughout
  • Documentation of the finished system for your insurer or future buyer
Learn more→

Metal Roof Over Shingles (Retrofit)

Retrofit metal installed over sound existing shingles: no tear-off, less waste, lower cost.

Included in your service

  • Honest deck and shingle assessment first, recover only when it is the right call
  • Furring strips or slip sheet as the panel profile and local code require
  • Existing vents, pipe boots, and flashings reworked to the new roof plane
  • Straight guidance on when tear-off is the better long-term choice
Learn more→

Metal Roof Repair

Targeted repair of damaged, loose, or storm-hit metal roofing before it reaches your ceiling.

Included in your service

  • Bent, dented, or punctured panels replaced and color-matched
  • Seams, laps, and penetrations resealed with compatible butyl and sealant
  • Failed pipe boots, closures, and ridge cap fasteners renewed
  • Written findings with photos of what we found and what we fixed
Learn more→

Metal Roof Leak Repair

Priority leak response: we trace the leak to its real source instead of caulking the symptom.

Included in your service

  • Water testing and interior tracing to find the true entry point
  • Backed-out fasteners, separated seams, and flashing gaps corrected at the cause
  • Emergency tarping available same day after a storm
  • Attic and insulation moisture check so hidden damage does not sit and spread
Learn more→

Screw Replacement & Re-Fastening

The top cause of leaks on 15 to 30 year old screw-down roofs, fixed for a fraction of replacement.

Included in your service

  • Every fastener replaced with oversized screws and new EPDM sealing washers
  • Dried-out washers and stripped holes addressed panel by panel
  • Ridge, eave, and sidewall closures renewed at the same time
  • Restores a watertight roof without replacing sound panels
Learn more→

Corrugated & Ribbed Panel Roofing

Corrugated, tuff-rib, and 5V panel roofing: the budget-friendly workhorse for homes and outbuildings.

Included in your service

  • Galvalume and painted steel panels cut to length on site
  • Correct screw pattern and torque so washers seat without over-driving
  • Foam and metal closures at ridge, eave, and rake to keep weather and pests out
  • Full color range for homes, cabins, barns, and workshops
Learn more→

Metal Shingle Roofing

The look of architectural shingle, slate, or shake with the lifespan and wind rating of steel.

Included in your service

  • Interlocking stamped steel or aluminum shingle panels
  • Walkable finished surface, easier to service than a standing seam field
  • Lightweight enough for retrofit over an existing roof structure
  • Profiles and colors that suit historic and HOA-governed neighborhoods
Learn more→

Stone-Coated Steel Roofing

Steel strength under a textured stone finish, with strong hail and wind performance.

Included in your service

  • Acrylic-bonded stone granule surface over structural steel
  • Battened or direct-to-deck installation depending on the profile
  • Class A fire rating and high impact resistance ratings
  • Tile, shake, and shingle textures for suburban and coastal homes alike
Learn more→

Copper & Specialty Metal Roofing

Copper, zinc, and aluminum for porches, bay windows, dormers, and full architectural roofs.

Included in your service

  • In-house fabrication of pans, valleys, and custom curved details
  • Soldered seams and joints where the detail calls for it
  • Isolation of dissimilar metals to prevent galvanic corrosion
  • A living patina that develops over decades of service
Learn more→

Metal Roof Coating & Painting

Restoration for faded, chalking, or surface-rusted metal, adding 10 to 15 years without replacement.

Included in your service

  • Wash, degrease, and mechanical prep of the entire panel surface
  • Rust treatment and primer on affected areas before topcoat
  • High-performance elastomeric or silicone coating system applied to spec
  • Honest assessment first: we say so when the roof is past coating
Learn more→

Flashing, Chimney & Skylight Repair

Flashing is the number one leak point on any metal roof, and it is what we fabricate best.

Included in your service

  • Custom bent step, counter, and apron flashing made in-house
  • Chimney crickets to shed water on the uphill side
  • Skylight curbs and head flashing rebuilt to the panel profile
  • Valley and wall transition details closed with matching trim
Learn more→

Snow Guards & Ice Protection

Snow retention that stops rooftop avalanches onto decks, gutters, walkways, and entryways.

Included in your service

  • Pad-style guards or continuous rail systems matched to your panel
  • Layout calculated from roof pitch, panel length, and local snow load
  • Clamp-on mounting on standing seam, no panel penetrations
  • Ice dam and eave detailing for higher-elevation homes
Learn more→

Storm & Wind Damage Repair

Wind, hail, and fallen-limb repair with thorough documentation and a straight repair-or-replace answer.

Included in your service

  • Free post-storm inspection with dated photo documentation
  • Emergency tarping and temporary weatherproofing when needed
  • A written report you can use when documenting your insurance claim
  • Honest assessment of repair versus replacement, with no pressure either way
Learn more→

Metal Roof Inspection

A written, no-obligation assessment of fastener condition, seams, flashing, and remaining service life.

Included in your service

  • Fastener, washer, and seam condition checked across the field
  • Flashing, penetrations, and closures inspected point by point
  • Coating wear, chalking, and corrosion graded panel by panel
  • Written report with photos and a straight answer on years remaining
Learn more→

Gutters for Metal Roofs

Gutters sized and hung correctly for metal roofing, where standard hangers and spacing do not work.

Included in your service

  • Seamless aluminum or half-round systems formed on site
  • Hanger placement and spacing matched to the panel profile
  • Oversized capacity and downspouts sized for heavy regional rainfall
  • Bracket spacing tightened for high-wind zones so storms do not tear the gutter off
Learn more→

Commercial & Agricultural Metal Roofing

Barns, workshops, churches, and light commercial metal roofing across the county.

Included in your service

  • Long-run panels for wide spans and low-slope structures
  • Purlin and framing attachment detailed for the building type
  • Insulation, vapor barrier, and condensation control options
  • Repairs and re-fastening for aging agricultural metal buildings
Learn more→
Verified client reviews

306+ Verified Client Reviews in Huntsville

⭐⭐⭐⭐⭐ 4.9/5 · 306 verified Google reviews

Free Quote

Get Your Free Quote

Metal Roofing in Huntsville · Response within 24h · No commitment · ☎ (256) 858-7133

Your Free Quote Request

Confidential · Response within 24h

✅ Free personalized estimate ⚡ Response within 24h 🛡️ Licensed & Insured 📍 On-site visits included in Huntsville ✅ No hidden fees 🕐 Available Mon-Sun 7am-7pm